Home  |  Lead Free Bronze Bushings

Elite Bushing is the premiere name in the niche of environmentally-friendly bearing and cast bar solutions and supplies leading producers of sustainable energy, marine, medical and other commercial products with high quality bronze bushings. Our eco-friendly alloy C87850 ECO Bronze is RoHS compliant and meets the lead-free safe drinking water act. The main difference between our ECO BRONZE and other lead-free alternatives is that ECO BRONZE

ECO BRONZE is probably the most tested lead-free bronze material to-date; it’s tough, non-galling, does not get brittle at high temperatures, superior impact and compressive strength, and a great bushing material. Eco Bronze has gained acceptability in the potable water pump industry as it is S3874 & AB1953 compliant, it’s also gained acceptance in other industries such as construction equipment, Wind tower, food processing, medical devices and many others due to its great bushing properties.

is a great bushing material

Other materials compromise their bushing properties to become lead-free, but ECO BRONZE has proved to be as good as, and in some cases superior to, the leaded material it has replaced.

Kingpin Bush Supplier

Lead Regulation :
Elite Engineering Lead Free Brass meets requirements of following directives.

Drinking Water :
European directive 1998/83/CE and other Countries directives which regulates the quality of drinking water.

RoHS :
European directive 2002/95/CE (Restriction of Hazardous Substances) applicable for the electrical and electronic industry.

European directive 2000/53/CE (End of life Vehicle) which aims at reducing waste arising from end-of-life vehicles.

European Union Regulation 1907/2006 (Registration, Evaluation, Authorisation and Restriction of Chemicals addresses the production and use of chemical substances, and their potential impacts on both human health and the environment.

C89835 Bismuth Tin Bronze

“Lead Free”C89835 is a “Lead Free” alternative for C93200 Bearing Bronze. When an application requires the properties of C932 Bearing Bronze but needs to be “lead free”, C89835 Bismuth Tin Bronze can be used. C89835 Bismuth Tin Bronze utilizes Bismuth as a Lead replacement. Bismuth and Lead both have relatively low solubility in copper alloys. As such, during casting, these elements solidify into low melt point pools through the alloy matrix, filling porosity voids and providing advantages for chip breakage during machining.

Application :

  • Pipe Fittings
  • Pump Components
  • Water Pump Impellers
  • Housings

Chemical Composition :-


C95400 Aluminum Bronze / C954 Aluminum Bronze

C95400 Aluminum Bronze is a tough, hard, aluminum bronze that resists wear, abrasion, and deformations under high compressive loads. When mating with dissimilar metals, C95400 Aluminum Bronze prolongs part life, cuts maintenance costs, friction, galling, and seizing are reduced.

  • Worm Gears
  • Adjusting Nuts
  • Collets
  • Plungers
  • Pump Rods
  • Sleeve Bearings
  • Valve Seats
  • Guide Pin Bushings
  • Industrial Bearings
  • Wear plates
  • Seals
  • Liners
  • Gibs and Ways

Chemical Composition

Min./Max.83.0 min10.0-11.53.0-5.0.501.5

C90300 (SAE620) Navy G Bronze / C903 High Tin Bronze

C90300 SAE 620 Tin Bronze is often used in high load, low speed applications. C903 Bronze has excellent wear properties. As the name may imply “Navy G” bronze is used in various marine applications due to its excellent resistance to corrosion. A member of the High Tin Bronze Alloy family C90300 Bronze is used in similar ways as the other alloys of this family.

Tin bronze alloys, such as C903, are typically found in gear, high-strength bushing, Brass Turning Parts Manufacture and bearing applications where high strength and low speeds and heavy loads are present. Other high-strength applications for these alloys are pump impellers, piston rings, steam fittings and valve bodies. C90300 tin bronze castings are utilized in movable bridge components, turntables for bridges and other structures for fixed and expansion bearings with slow or intermittent movement with heavy loads.


  • Gears
  • Worm Gears
  • Valves
  • Seal Rings
  • Pump Impellers
  • Valve Bodies
  • Bushings

Specifications :


Equivalent designations to UNS C90300 alloy include:

  • ASTM B271
  • ASTM B30
  • ASTM B505
  • ASTM B584
  • ASTM B763
  • MIL C-11866
  • QQ C390
  • SAE J461
  • SAE J462